Motorcycle Carrier/Hitch rack, Goldwing hauler, 1000 lbs capacity, Adjust receivr

  

All of the other carriers loose their shape, bend after 1 or 2 trips! The highways are typically very rough(particularly if hauling with a motorhome) when you carry a motorcycle more than 400 lbs out there. Don't be caught with a carrier that falls apart on you! US designed and built, Heavy duty motorcycle rack/hitch carrier. It is the Sturdiest, most over-designed CYCLE RACK AVAILABLE!

Side Supports are used so the main. Carrying tray is supported in 3 places. This is necessary to keep the carrying tray from bending during usage. The less expensive motorcycle carriers DO NOT HAVE THIS FEATURE and the tray bends downward after a short trip! THIS CARRIER HAS ADJUSTMENT TO KEEP THE MOTORCYCLE CLOSE TO BACK OF VEHICLE.

Don't overload your hauling vehicle by being limited to the manufacturers excess stickout! Place the bike 2 off the back of the hauling vehicle.

Motorcycle Carrier/ hitch rack, Class 3 or 4 hitch required(2" square receiver)for up to 1000 lb capacity(quite often the hauling vehicle may be the limiting factor) This rack is for the larger and heavier motorcycles up to 89" long wheel end to end. The tires shouldn't be wider than 200 mm or 8.75 to fit inside the tray. THIS CARRIER CANNOT BE USED ON 5TH WHEEL OR TRAVEL TRAILER TYPE VEHICLES, THEY ARE RATED FOR 100-200 LBS TONGUE WEIGHT! These modular, high quality, all steel units are manufactured in the US by motorcycleracks. THESE HITCH RACKS ARE THE ONLY CYCLE CARRIERS IN THIS CLASS WHERE THE DEVICE Deploys (2) vertical stabilizer bars to provide isolation from the vehicle and control the sway of the larger motorcycles for closer positioning to the vehicle plus improved ground clearance.

Most of the competitors have NO ADJUSTMENT ON THE CARRYING TRAY and the motorcycles sticking out there 5-13 more that is necessary and this tends to overload the vehicle! The motorcycle should be positioned as close as possible to the vehicle but never touch it for the best "drive-ability" possible. The steel tray accommodates a few different types of motorcycles of different length for a near perfect balance of the carrier on the suv, van or truck!! The carrier is modular in design and is interchangeable for optimizing the set-up and for later upgrades/changes to the tray size and receiver bracket for adaptability on other vehicles.

(in case you change hauling vehicle or cycle). Other accessories can be readily added later as you get experience with the carrier i.

Bolt on or magnetic lights and other stabilizer bars to simplify the tie down process. The dimension on the carrier shown here in all of the photos are: 18 and 22 (you have your choice of either dimension on the carrier) from hitch pin to center of cycle tray. It is fully adjustable by moving the tray on the receiver assembly to the other bolt pattern available. Some Motorcycles and particularly the big scooters.

Are inherently slightly weighted toward the rear due to the rear engine mounting. To offset this weight and not overload the hitch by excess twist(torsion), the mounting position can be adjusted on the carrier by selecting the proper holes. The carrier comes complete with a 9.25" wide x 60" long heavy duty loading ramp for a gentle incline. The receiver has the integrated anti-wobble/anti-tilt and a pair of cam lock style tie downs to strap the wheels to the tray. The carrier consists of a heavy duty welded steel receiver assembly with side supports, main carrier tray measuring 8.25" wide x 85" long with front wheel chock, 2 vertical stabilizer bars, 1 horizontal sta-bar, and a loading ramp measuring 9.25" wide x 60" long.

You add 2-4 tie downs. The integrated anti-chock/anti-tilt is guaranteed to work on ANY HITCH.

(the anti-tilt collar type offered by others do not work on many factory hitches including many GM factory hitches) THIS CARRIER ALSO HAS 4 HEAVY DUTY TIE DOWN POINTS, most of the competition usually offers 2. Tie down points with thin bracketry. Typical cycles that will fit on this carrier: Harley Davidson: 2016 and older fatbobs, softtail, crossbones, all dressers: ALL HD Softails w/190mm rear tires max. All BMW, Ducati, Honda Gold wings, VTX1300/1800, Suzuki HyaBussa, Suz Blvd, Honda St1300, DN-01 cruisers, VTX1300/1800, Interceptors, Shadows, Nighthawks, CBR; Yamaha: FZ6, FV1-1100, Yam FJR1300, Vstars, etc. Send specific questions on your application: saslavick at yahoo dot com The questions will be answered within 1 day! The only stock cycles it will not take are Victories and the Vrods/Wrods due to the excessively wide 240mm rear tires. THE ASSUMPTIONS FOR THESE BIKES TO FIT YOUR HAULING VEHICLE ARE: 1. Hitch height to ground is 14 or more. The face of the hitch is flush to the end of the bumper of fascia(or the furthest protruding surface) +/- 1. Also, no other equipment is in the way such as Rear Mounted spare tires and on motor-homes: rear mounted tires, ladders, gas fill tube or exhaust pipe for the motor-home. I have a wide tray design for the Suzuki Blvd or 2018 fat boy/bob with the 240mm rear tire and approx.

Just ask me about it. For a technical and application website on these cycle carriers. Video on how loading a Honda Goldwing/how the loading works. COPY THIS LINK TO YOUTUBE TO VIEW IT or go to youtube and in the search window say.

Loading honda goldwing onto hitch carrier. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Towing Parts & Accessories\Trailer Hitches". The seller is "sslavick" and is located in this country: US. This item can be shipped to United States.

• Shape: carrying tray =channel
• Custom Bundle: yes
• Items Included: Mounting Hardware
• Country of Manufacture: United States
• Item Length: 85
• Placement on Vehicle: Rear
• Tow Weight Capacity: 0
• Shank Diameter: 2 in
• Manufacturer Warranty: 2 Year
• Features: Heavy Duty, Multiple Mounting Holes, Rust-Resistant
• Finish: powder coated all parts
• Hitch Class: 3,4,5
• Part Type: Large road motorcycle carrier
• Performance Part: Yes
• Mounting Style: receiver hitch
• Non-Domestic Product: No
• Trailer Hitch Type: Receiver Hitch
• Color: Gray
• Manufacturer Part Number: 3CD8-85-22-2DS-R960 GW
• Material: Carbon Steel
• Tongue Weight Capacity: 1000 lbs
• Modified Item: No
• Brand: Motorcycleracks.net
• Type: Class 3,4,5
• OE/OEM Part Number: none
• Part Brand: Motorcycleracks.net/SAS LLC
• Receiver Tube Size: 2in.
• Country/Region of Manufacture: United States
• Universal Fitment: Yes
• Item Weight: 1115